S
seper8tor
New member
Equipment
M5660
- May 9, 2024
- 2
- 0
- 1
- Vista CA
Yesterday at 9:58 PM
- #1
So I recently purchased a 2022 M5660 tractor for our new 15 acre property. My first tractor ever and Ive got about 15 hours on it. I had a front rake attachment and was plowing through some scrub oak trying to clear a path through some live and dead oak saplings. A small(1" diameter) sapling I ran over speared the hydraulic lines on the left side of the tractor at just the right angle and took out a hose that I think feeds the LA1154 loader. I didn't notice at first until all of a sudden the loader and the rear box blade stopped working. Since I was in the middle of a bunch of brush and both front and back hydraulics were non functional and on the ground I couldn't move and had to leave my tractor in the bushes.
My question is, how much fluid did I lose breaking that hose? Its the one coming off the protected box next to the left side step that connects to the loader with the 90 degree metal L connector. DId I lose all 10 gallons? I shut down the tractor right after the loader and 3 point stopped working and after I noticed the big puddle of fluid on the ground! I'm trying to figure out how much fluid I need to order to get back up and running after I replace the hose.
After I replace the hose can I just top off the hydraulic fluid and get back to work or is there some other process I need to do? Bleeding?
Thanks for any help!
Last edited:
jyoutz
Well-known member
Equipment
MX6000 HST open station, FEL, 6’ cutter, forks, 8’ rear blade, 7’ cultivator
- Jan 14, 2019
- 2,619
- 1,707
- 113
- Edgewood, New Mexico
Yesterday at 11:02 PM
- #2
seper8tor said:
So I recently purchased a 2022 M5660 tractor for our new 15 acre property. My first tractor ever and Ive got about 15 hours on it. I had a front rake attachment and was plowing through some scrub oak trying to clear a path through some live and dead oak saplings. A small(1" diameter) sapling I ran over speared the hydraulic lines on the left side of the tractor at just the right angle and took out a hose that I think feeds the LA1154 loader. I didn't notice at first until all of a sudden the loader and the rear box blade stopped working. Since I was in the middle of a bunch of brush and both front and back hydraulics were non functional and on the ground I couldn't move and had to leave my tractor in the bushes.
My question is, how much fluid did I lose breaking that hose? Its the one coming off the protected box next to the left side step that connects to the loader with the 90 degree metal L connector. DId I lose all 10 gallons? I shut down the tractor right after the loader and 3 point stopped working and after I noticed the big puddle of fluid on the ground! I'm trying to figure out how much fluid I need to order to get back up and running after I replace the hose.
After I replace the hose can I just top off the hydraulic fluid and get back to work or is there some other process I need to do? Bleeding?
Thanks for any help!
With tractor engine off. Work the loader joystick to remove any potential pressure. Then disconnect the broken hose, take it to a hydraulic shop and have them make a replacement. Install new hose, start and run the machine and work the loader. Shut off the engine and top off the hydraulic fluid. No bleeding necessary, just move the loader a few times before topping off the fluid. Use genuine Kubota UDT or SUDT, whatever the manual recommends.
Reactions:1 users
Runs With Scissors
Well-known member
Equipment
L2501 TLB , Grappel, Brush Hog, Box Blade, Ballast box, Forks, Tiller, PH digger
- Jan 25, 2023
- 1,991
- 2,130
- 113
- Michigan
Today at 2:05 AM
- #3
@jyoutz has a good idea.
As far as the amount of fluid lost thats hard to tell.
I would look at the hydraulic fluid level indicator (stick or sight glass?)to see if it is registering anything.
Then if you still cant tell, you may as well order the full amount. You will be needing some for the hourly servicing anyway.
BTW, Congratulations on the new machine!
Reactions:1 user
TheOldHokie
Well-known member
Lifetime Member
Equipment
L3901/LA525, B7200DT/B1630, G2160/RCK60, G2460/RCK60
Today at 5:31 AM
- #4
seper8tor said:
So I recently purchased a 2022 M5660 tractor for our new 15 acre property. My first tractor ever and Ive got about 15 hours on it. I had a front rake attachment and was plowing through some scrub oak trying to clear a path through some live and dead oak saplings. A small(1" diameter) sapling I ran over speared the hydraulic lines on the left side of the tractor at just the right angle and took out a hose that I think feeds the LA1154 loader. I didn't notice at first until all of a sudden the loader and the rear box blade stopped working. Since I was in the middle of a bunch of brush and both front and back hydraulics were non functional and on the ground I couldn't move and had to leave my tractor in the bushes.
My question is, how much fluid did I lose breaking that hose? Its the one coming off the protected box next to the left side step that connects to the loader with the 90 degree metal L connector. DId I lose all 10 gallons? I shut down the tractor right after the loader and 3 point stopped working and after I noticed the big puddle of fluid on the ground! I'm trying to figure out how much fluid I need to order to get back up and running after I replace the hose.
After I replace the hose can I just top off the hydraulic fluid and get back to work or is there some other process I need to do? Bleeding?
Thanks for any help!
Replace the hose, top off, and go.
Your tractor pump is rated for roughly 10 gallons per minute at full engine rpm so it could easily dump multiple gallons if it ran very long after the rupture. If it were me I would have at least 5 gallons with me when I returned to the scene and I would buy at least two 5 gallon pails just in case. It does not go bad and you should always have a supply on hand.
I also suggest you look closely at the damsge - its quite possible you broke a fitting off along with the hose.
Dan
Last edited:
Reactions:1 users
S
seper8tor
New member
Equipment
M5660
- May 9, 2024
- 2
- 0
- 1
- Vista CA
Today at 6:14 AM
- #5
Thanks for the responses! I think I'll pull the hose monday and inspect the fittings. Then I'll call around and try to find the hose and fluid. That fluid is expensive! I think I read somewhere that NAPA parts could make up a new hose if the local Kubota shop doesn't have one.
jyoutz
Well-known member
Equipment
MX6000 HST open station, FEL, 6’ cutter, forks, 8’ rear blade, 7’ cultivator
- Jan 14, 2019
- 2,619
- 1,707
- 113
- Edgewood, New Mexico
Today at 6:27 AM
- #6
seper8tor said:
Thanks for the responses! I think I'll pull the hose monday and inspect the fittings. Then I'll call around and try to find the hose and fluid. That fluid is expensive! I think I read somewhere that NAPA parts could make up a new hose if the local Kubota shop doesn't have one.
NAPA or any hydraulic shop. Just take them the old hose and fittings. And yeah the other posters offered good advice to have the fluid on hand and top off before reassembly and again after you get it back together and operate the loader. With a 2022 model, you will need SUDT fluid.
Runs With Scissors
Well-known member
Equipment
L2501 TLB , Grappel, Brush Hog, Box Blade, Ballast box, Forks, Tiller, PH digger
- Jan 25, 2023
- 1,991
- 2,130
- 113
- Michigan
Today at 8:26 AM
- #7
TheOldHokie said:
I would buy at least two 5 gallon pails just in case.
Last time I was at the dealer, I asked for a 5 gallon pail, and the manager suggested to me that (5) one gallon jugs is much easier to handle/pour and that I would only be saving like $1.36 by getting a single 5 gallon jug.
Sounded reasonable to me, so thats the way I went.
TheOldHokie
Well-known member
Lifetime Member
Equipment
L3901/LA525, B7200DT/B1630, G2160/RCK60, G2460/RCK60
Today at 8:35 AM
- #8
Runs With Scissors said:
Last time I was at the dealer, I asked for a 5 gallon pail, and the manager suggested to me that (5) one gallon jugs is much easier to handle/pour and that I would only be saving like $1.36 by getting a single 5 gallon jug.
Sounded reasonable to me, so thats the way I went.
Thats odd. Around here SUDT2 is $28/ gallon in a 5 gallon pail. How does that compare to what you paid?
Dan
Last edited:
R
Russell King
Well-known member
Equipment
L185F, Modern Ag Competitor 4’ shredder, Rhino tiller, rear dirt scoop
- Jun 17, 2012
- 4,847
- 1,086
- 113
- Austin, Texas
Today at 11:12 AM
- #9
Runs With Scissors said:
Last time I was at the dealer, I asked for a 5 gallon pail, and the manager suggested to me that (5) one gallon jugs is much easier to handle/pour and that I would only be saving like $1.36 by getting a single 5 gallon jug.
Sounded reasonable to me, so thats the way I went.
1 gallon jugs are a LOT easier to carry to the tractor than 5 gallon pails!
TheOldHokie
Well-known member
Lifetime Member
Equipment
L3901/LA525, B7200DT/B1630, G2160/RCK60, G2460/RCK60
Today at 11:17 AM
- #10
Russell King said:
1 gallon jugs are a LOT easier to carry to the tractor than 5 gallon pails!
Five at a time
Dan
D
DustyRusty
Well-known member
Equipment
2020 BX23S, BX2822 Snowblower, Curtis Deluxe Cab,
- Nov 8, 2015
- 5,555
- 4,167
- 113
- North East CT
Today at 11:50 AM
- #11
I will be the one dissenting voice. You purchased a tractor, when it sounds like you should have started with a bulldozer or a tracked skid steer to clear the land and then the tractor to work the land. Good luck repairing the tractor.
Show hidden low quality content
You must log in or register to reply here.